A TLY-5 PCB is a printed circuit board constructed using Taconic TLY-5 laminate, a ceramic-filled PTFE material optimized for high-frequency applications. TLY-5 combines low dielectric loss, stable dielectric constant, and thermal reliability, making it suitable for RF, microwave, and high-speed digital circuits. TLY-5 PCBs are widely used in: Wireless communication modules High-speed networking equipment RF...
A Satellite PCB is a printed circuit board designed for use in satellite systems and spacecraft electronics, where extreme environmental conditions and high reliability are critical. Unlike terrestrial PCBs, satellite PCBs must operate under wide temperature variations, intense radiation, vacuum, and mechanical vibration, while maintaining electrical performance over long mission durations. Satellite PCBs are employed...
A Blind Via PCB is a multilayer printed circuit board that uses vias connecting an outer layer to one or more inner layers without extending through the entire board. Unlike through-hole vias, blind vias do not penetrate all layers, allowing for high-density routing, reduced board size, and improved signal integrity. Blind via technology is critical...
A Multilayer HF PCB is a printed circuit board engineered for high-frequency signal transmission across multiple layers. Unlike standard multilayer boards, HF (high-frequency) PCBs are optimized for low dielectric loss, controlled impedance, and minimal crosstalk, enabling high-speed signal integrity in demanding applications. Multilayer HF PCBs are commonly used in: RF and microwave modules Wireless communication...
A 5G Router PCB is a high-performance printed circuit board designed to enable ultra-fast data transmission, low latency, and stable wireless connectivity in modern communication systems. Unlike traditional router boards, 5G routers must handle multi-gigabit data rates, high-frequency RF signals, and complex multi-antenna (MIMO) architectures. Typical 5G router PCB systems integrate: RF front-end modules (power...
An RF-35 PCB is a printed circuit board built using Taconic RF-35 laminate, a ceramic-filled PTFE-based material designed for high-frequency applications. With a dielectric constant of approximately 3.5 and a low dissipation factor, RF-35 provides a balance between signal performance, thermal stability, and manufacturability. Compared to standard FR-4, RF-35 significantly reduces signal loss at high...
An RO4350B PCB is a printed circuit board built using Rogers RO4350B laminate, a widely adopted high-frequency material known for its low dielectric loss, stable dielectric constant (Dk ≈ 3.48), and excellent thermal reliability. Unlike traditional PTFE-based materials, RO4350B is a hydrocarbon ceramic laminate, which combines high-frequency performance with easier manufacturability similar to standard FR-4...
An RF Test PCB is a printed circuit board engineered to support high-frequency testing, characterization, and validation of RF and microwave components. Unlike standard PCBs, RF test boards are optimized for signal integrity, controlled impedance, and minimal insertion loss, ensuring that measurements accurately reflect the performance of devices under test (DUT). RF test PCBs are...
A Burn-in PCB is a printed circuit board specifically designed to support reliability testing of electronic components under elevated temperatures, voltage stress, or operational load. Burn-in testing identifies early-life failures and verifies long-term performance, making these PCBs critical for semiconductor validation, power electronics, and high-reliability systems. Burn-in PCBs are widely used in: Semiconductor testing laboratories...
A BT Epoxy PCB is a printed circuit board that uses Bismaleimide-Triazine (BT) resin as the substrate material. BT Epoxy offers low coefficient of thermal expansion (CTE), high glass transition temperature (Tg), and excellent dimensional stability, making it ideal for multilayer, high-density, and fine-pitch applications. BT Epoxy PCBs are particularly suitable for: High-performance computing and...
KKPCB is a leading electronic solutions provider specializing in PCB design, fabrication, assembly, and testing for Flex, Rigid-Flex, RF/Microwave, HDI, rigid multilayer, and ATE test boards. We offer comprehensive end-to-end services, including prototyping, component sourcing, SMT/THT assembly, functional testing, enclosure assembly, and final product packaging. With our one-stop, in-house capabilities, KKPCB delivers OEM and ODM solutions with fast turnaround, high quality, and cost-effective results, serving clients worldwide.
PCB Manufacturing
PCB Assembly
Technical Support