ITEQ IT-180A Datasheet: High-Tg FR-4 Laminate (IT-180ATC) and PDF

November 21, 2026by kkpcb020
ITEQ IT-180A is a high-Tg, lead-free FR-4 laminate and prepreg system from ITEQ Corporation, built for high-reliability multilayer boards. The laminate is sold as IT-180ATC and the prepreg as IT-180ABS. Its DSC Tg of 175 °C, low Z-axis expansion and CAF resistance make it a common choice for automotive electronics, networking equipment, high-layer-count PCBs and heavy-copper boards. This page summarises the official ITEQ IT-180A data sheet, compares it with IT-158 and IT-170GRA1 and explains how KKPCB builds IT-180A PCBs. The full PDF data sheet can be downloaded at the end.

ITEQ IT-180A PCBs for networking and automotive electronics
IT-180A is used in networking, automotive and high-layer-count boards

1. What Is ITEQ IT-180A?

IT-180A is an ANSI FR-4.0 epoxy-glass material that ITEQ describes as “High Tg / Lead Free / High Reliability”. It is one of ITEQ’s most widely used high-Tg grades. The data sheet lists it against IPC-4101 /98, /99, /101 and /126 for laminate, and IPC-4103 /250 and /550.

ITEQ highlights four characteristics:

  • Excellent CAF resistance and good through-hole reliability.
  • Low CTE in Z and in X/Y, with high thermal reliability.
  • Lead-free compatibility for high-temperature assembly.
  • Target uses: automotive, high-layer PCBs, networking and heavy-copper applications.

IT-180A, IT-180ATC and IT-180ABS naming

On the current data sheet (W-CTE-1002-34C), ITEQ uses IT-180A as the product family name, IT-180ATC as the copper-clad laminate code and IT-180ABS as the prepreg code. Material lists that show “IT180TC” or “IT-180ATC” refer to the same laminate, so one data sheet covers all three names.

2. ITEQ IT-180A Key Specifications

Values below are the typical values published by ITEQ. Dk and Df are given at 50% resin content.

Property IPC-TM-650 method Typical value
Glass transition temperature (DSC / DMA) 2.4.25 / 2.4.24.4 175 / 185 °C
Decomposition temperature (5% weight loss) 2.4.24.6 345 °C
Z-axis CTE, alpha 1 / alpha 2 2.4.24 45 / 210 ppm/°C
Z-axis expansion, 50–260 °C 2.4.24 2.7%
X/Y CTE (40–125 °C) 2.4.41 / 2.4.24.5 11–13 / 13–15 ppm/°C; 11 / 12 ppm/°C
T260 / T288 2.4.24.1 >60 / 20 min
Permittivity (Dk) at 1 MHz / 1 GHz 2.5.5.9 4.5 / 4.4
Loss tangent (Df) at 1 MHz / 1 GHz 2.5.5.9 0.014 / 0.015
Peel strength, 35 µm low-profile / standard copper 2.4.8 5 / 8 lb/in
Volume resistivity 2.5.17.1 1×109 MΩ·cm
Surface resistivity 2.5.17.1 1×108 MΩ
Moisture absorption, max. 2.6.2.1 0.10%
Flexural strength, LW / CW 2.4.4 500–530 / 410–440 N/mm²
Young’s modulus, warp / fill ASTM D3039 19 / 18 GPa
Thermal stress, 10 s at 288 °C 2.4.13.1 Pass (unetched and etched)
Flammability UL94 V-0
CTI ASTM D3638 / UL 746 CTI 3 (175–249 V)
Maximum operating temperature UL 746 130 °C
ITEQ IT-180A data sheet laminate properties
Laminate properties from the official ITEQ IT-180A data sheet

What the ITEQ IT-180A numbers mean in practice

  • 175 °C Tg with 2.7% Z-expansion: together these keep stress on plated through-holes low in thick boards and through multiple reflow cycles.
  • Low X/Y CTE: helps limit stress at solder joints of large components and keeps dimensional movement small during sequential lamination.
  • Dk 4.4 / Df 0.015 at 1 GHz: standard FR-4 electrical performance. It suits control, power and moderate-speed digital signals, but it is not a low-loss material.
  • 130 °C UL MOT: the maximum continuous operating temperature recognised by UL for this material.

3. ITEQ IT-180A vs IT-158 and IT-170GRA1

ITEQ offers mid-Tg, high-Tg and halogen-free mid-loss grades. The table compares IT-180A with two neighbours, using each grade’s own ITEQ data sheet.

Property IT-158 IT-180A IT-170GRA1
Positioning Middle Tg, lead free High Tg, lead free High Tg, halogen free, mid-loss
Tg, DSC (°C) 155 175 180
Td (°C) 345 345 380
Z-expansion 50–260 °C 3.3% 2.7% 2.7%
T288 (min) 20 20 >60
Dk / Df @ 1 GHz 4.3 / 0.016 4.4 / 0.015 3.9 / 0.008
IPC-4101 slash sheets /98 /99 /101 /98 /99 /101 /126 /127 /128 /130
ITEQ IT-180A vs IT-158 and IT-170GRA1 comparison chart
IT-180A compared with IT-158 and IT-170GRA1

How to choose:

  • IT-158 for mid-Tg boards where cost matters and thermal stress is moderate.
  • IT-180A for high-layer-count, thick, heavy-copper or automotive boards that need a 170 °C class Tg.
  • IT-170GRA1 when the design must be halogen-free or needs lower loss (ITEQ lists Dk 3.8 and Df below 0.009 at 10 GHz).

4. ITEQ IT-180A Compared with Other High-Tg FR-4 Grades

Designers often ask whether IT-180A can be replaced by another high-Tg FR-4. Shengyi S1000-2 and Kingboard KB-6167F are in the same class. Their data sheets give similar Tg, Td and Z-expansion values, but they are different resin systems. Specimens and test conditions also differ between suppliers.

ITEQ IT-180A compared with Shengyi S1000-2 and Kingboard KB-6167F
High-Tg FR-4 grades from three suppliers

A substitution should therefore be approved by the designer, and controlled-impedance lines should be recalculated with the new material’s construction data. See our Shengyi S1000-2 datasheet guide for that material’s full property table.

5. Building ITEQ IT-180A PCBs at KKPCB

IT-180A is one of the FR-4 systems listed on the KKPCB PCB manufacturing capabilities page. For IT-180A builds, KKPCB:

  • Uses IT-180ATC cores with IT-180ABS prepreg so the resin system is matched throughout the stack-up.
  • Models impedance with the Dk of the selected glass style and resin content. Our standard tolerance is ±5 Ω below 50 Ω and ±10% at or above 50 Ω.
  • Supports high-layer-count and HDI constructions. Designs above 30 layers are reviewed by engineering.
  • Supports heavy-copper designs up to 14 oz finished outer copper, with line/space rules matched to copper weight.
  • Holds standard warpage at or below 0.75%. Tighter limits are reviewed case by case.

For automotive programmes, see our automotive PCB assembly page. Other base materials are compared on our PCB materials page.

6. Typical Applications of IT-180A

  • Automotive electronics.
  • Networking and telecom equipment such as switches and routers.
  • High-layer-count multilayer PCBs and backplanes.
  • Heavy-copper power boards that see high thermal load during assembly.

7. Download the ITEQ IT-180A Data Sheet (PDF)

The official ITEQ IT-180A data sheet (document W-CTE-1002-34C) is shown below. It covers laminate properties, test methods and the applicable IPC specification sheets.

Download the ITEQ IT-180A data sheet (PDF)

Source: ITEQ Corporation, IT-180A data sheet W-CTE-1002-34C. All rights to the data sheet belong to ITEQ Corporation; values are typical and for reference only.

Frequently Asked Questions

What is the Tg of ITEQ IT-180A?
ITEQ gives 175 °C by DSC and 185 °C by DMA.
Is IT-180ATC the same as IT-180A?
Yes. IT-180ATC is the laminate code and IT-180ABS is the prepreg code of the IT-180A system, according to the ITEQ data sheet.
Is ITEQ IT-180A halogen-free?
The IT-180A data sheet does not describe it as halogen-free. For a halogen-free high-Tg ITEQ material, look at grades such as IT-170GRA1.
Is IT-180A suitable for high-speed designs?
With Df of 0.015 at 1 GHz, IT-180A is a standard-loss FR-4. It is fine for many digital designs, but long multi-gigabit channels usually need a mid-loss or low-loss material.
Does KKPCB build ITEQ IT-180A boards?
Yes. IT-180A is listed among KKPCB’s FR-4 systems. Specify it in your fabrication drawing and we will confirm stack-up and availability during quotation.

Quote Your ITEQ IT-180A PCB with KKPCB

Send your Gerber files, stack-up and impedance requirements to KKPCB, and our engineers will review the ITEQ IT-180A build before production. Contact KKPCB for a quote.

Leave a comment

Your email address will not be published. Required fields are marked *